EPDM Commercial Roofing Accessories

Use: JM 3 oz Polyester Slipsheet is intended for use as a separation layer between an existing roof system and a new single ply recover system.

Material: 3.0 oz/yd2 (102 g/m2 ) needle-punched, non UV-resistant polyester fabric.

Color: White

JM EPDM 10” RPS (Reinforced Perimeter Strip) is a 10" (25.4 cm) wide, 45 mil (1.14 mm) thick, polyester scrim reinforced, cured EPDM strip with a factory-laminated, 3" (7.62 cm) self-adhering seam tape along each edge. It is used to secure EPDM membrane from underneath in perimeters and corners and as additional securement as specified in Johns Manville specifications and details. Also consider using with the JM EPDM Peel & Stick 6" RTS (Reinforced Termination Strip) as part of a comprehensive peel & stick perimeter reinforcement system.

JM EPDM Peel & Stick Flashing is a 6", 9", and 12" (30.48 cm) wide, uncured EPDM (ethylene propylene diene monomer) sheet with a diamond texture on the top side with a release liner and a factory laminated, self-adhering EPDM/butyl tape. This product is formulated to provide high initial strength in both peel and shear at typical rooftop temperatures. It also improves the speed and quality of flashings on JM EPDM roofing systems.

JM EPDM Peel & Stick Inside/Outside Corners consist of 60 mil thick (1.5 mm) uncured flashing with a pre-applied peel and stick tape.

JM EPDM Peel & Stick Pipe Boots speed the flashing installation process and improve the quality of flashings on JM EPDM roofing systems. The pipe boots are specifically designed for round, roof penetrations eliminating the need for field-fabrication. The large double-thick molded ribs, at the top of each step, offer superior tear resistance as well as a cutting guide.

JM EPDM Peel & Stick Pipe Boots are formulated to provide high initial strength in both peel and shear at typical rooftop temperatures.

JM EPDM Pourable Sealer Pockets are one-piece, prefabricated units with a
2 1/2" (6.4 cm) wide base flange. Each pocket has a pre-applied pressure sensitive tape on the bottom of the base flange. This provides quick installation and excellent uniform bonding to the membrane.

Use to seal difficult-to-flash penetrations through the membrane.
 

JM EPDM Peel & Stick Sealing Strip is a cured, 6" (15.24 cm), 9" (22.86 cm) or 12" (30.48 cm) wide, EPDM (ethylene propylene diene monomer) strip with a matte finish and factory laminated, self-adhering seam tape. This product is formulated to 1) provide high initial strength in both peel and shear at typical rooftop temperatures, 2) improve the speed of application, and 3) improve the quality and performance of the lap on JM EPDM roofing systems.

JM EPDM Peel & Stick T-Joint Patches are 6" (15.24 cm) round, uncured EPDM (ethylene propylene diene monomer) sheets with a factory laminated, self-adhering EPDM/butyl tape. This product is formulated to 1) provide high initial strength in both peel and shear at typical rooftop temperatures and 2) improve the speed and quality of field seaming on JM EPDM roofing systems.

JM EPDM Peel & Stick Walkpads are a safe, simple, economical solution to protect roofs from damaging foot traffic. These heavy-duty, solid rubber pads are designed for the roofing industry. The nonporous surface is not affected by freeze/thaw conditions and stays in place when attached to the roof. Walkpads can be used on new or existing roofs. They provide a safe, stable and maintenance-free walkway for quick and easy access to rooftop equipment in high traffic areas.

JM EPDM Pre-Taped Curb Flashing is produced with 60 mil (1.52 mm) thick, EPDM with a release liner and a 3" or 6" factory laminated, self-adhering EPDM tape to efficiently flash curbs with a consistent, clean appearance.

JM EPDM Protective Stone Mat is a nominal 7.0 oz/yd2 (237.34 g/m2) UV-resistant, polypropylene, needle-punched fabric.

Use the JM EPDM Protective Stone Mat as a slipsheet between the membrane and the ballast or pavers.

JM EPDM Reinforced Termination Strip (RTS) With Tape is a black, 6" (15.24 cm) wide, 45 mil (1.14 mm) thick, polyester scrim reinforced, cured EPDM strip with a factory-laminated, 3" (7.62 cm) self-adhering seam tape.

JM EPDM Seam Tape Plus is a 3" or 6" (7.62 cm or 15.24 cm) wide, self-adhering, extruded EPDM (ethylene propylene diene monomer) splice tape providing superior adhesion between EPDM sheets. This product is formulated to improve the speed and quality of lap seaming on JM EPDM roof systems. Each box of JM EPDM Seam Tape Plus includes scrubber pads and handle for seam priming.

Use: JM Polyester Mat Protection Slipsheet is intended for use as a separation layer between extruded polystyrene insulation and roofing membrane in protected membrane (inverted) roof assemblies, as well as a separating sheet in some recover systems. It is also used as a protective layer between pavers and JM single ply membrane.

Material: 9.0 oz/yd2 (305.15 g/m2 ) needle-punched, UV-resistant polyester fabric.

Color: White

Use: Provides a visual and physical safety warning on roof top areas of caution and potential hazards including designation of the roof perimeter.

Material: 55 mil (1.40 mm) total thickness, comprised of 30 mil (0.76 mm) yellow non-reinforced TPO membrane laminated to 25 mil (0.64 mm) white cured seaming tape.

Colors: Yellow

Polymer Batten Strips are 1" (2.54 cm) wide, approximately .050" (1.27 mm) thick, plastic strips, prepunched 6" (15.24 cm) on center.

Anchor Bars are 1" (2.54 cm) wide, prepunched and counter-sunk, Galvalume®*-coated steel strips.

Use: Single Ply Membranes

Materials: Battens - Polymer
                   Anchor Bars - Galvalume-Coated Steel

Color: Battens - White
            Anchor Bars - Grey

Deck Types: Steel, Wood and Structural Concrete

* Galvalume is a registered trademark of BIEC International, Inc. and some of its licensed producers.